WebCAE
WebCAE PlatformUnified FEA & CFD simulation platform: Browser WebAssembly + Native Desktop

Inspect pre-solved models in your browser in 2 seconds (up to 300k DOF) or solve 1.5M+ DOF assemblies 100% offline on Windows, macOS, and Linux.

Browser WASM
Up to 300k DOF · 2s load
Native Desktop (Pro)
Up to 1.5M+ DOF · 100% offline
Physics & Solvers
Static, Modal, Kσ, Contact, CFD
3-Stage Snap-Fit Cycle · 10 N Pinch Release · 6.6k TET10 · 17 StepsMachinery3D Solid B-Rep

Side-Release Snap-Fit Buckle Assembly: Insertion, 10 N Pinch Disengagement & Extraction Cycle

Geometrically nonlinear 3D contact assembly simulation (Total Lagrangian + unilateral frictionless Mortar contact on quadratic TET10 elements) of a two-body polymer side-release buckle driven exclusively by prescribed displacements across 17 steps: axial insertion and snap-lock into side windows, 10 N transverse pinch release, and reverse extraction.

Side-release snap-fit buckles must balance low insertion effort during axial engagement against reliable retention on the locking ledges, while allowing ergonomic manual release under a ~10 N finger pinch force. The simulation resolves the complete 17-step physical cycle starting and ending in the unloaded separated state: (1) axial insertion along the 1:4 entry guide ramps through the 0.70 mm radial interference throat into the side release windows; (2) inward transverse displacement applied to the side pinch pads until the locking hooks clear the throat at F_pinch = 10.09 N; and (3) axial extraction back out of the housing.

✓ Unilateral Frictionless Mortar Contact on Quadratic 3D Solids (P2 / TET10)✓ Total Lagrangian Cauchy Stress & Green–Lagrange Strain Postprocessing✓ Displacement-Controlled 3-Stage Cycle (Insertion → 10 N Pinch → Extraction, 17 Steps)✓ Exact 3D Nodal Reaction Force Evaluation on Drive & Pinch Pads
Pre-solved .wce container ready
2 bodies · 6,626 TET10 (38,943 DOF) · 17 steps (3 stages) · F_pinch = 10.09 N · |u_el| = 1.24 mm · σ_vm = 12.5 MPa
Open in Web App (WASM) →
Opens directly on the Results tab in 2 seconds without re-solvingNeed 1.5M+ DOF offline? Get Pro ↓
Side-Release Snap-Fit Buckle Assembly: Insertion, 10 N Pinch Disengagement & Extraction Cycle
2 bodies · 6,626 TET10 (38,943 DOF) · 17 steps (3 stages) · F_pinch = 10.09 N · |u_el| = 1.24 mm · σ_vm = 12.5 MPaLaunch 3D ↗
Assembly & Mesh
2 STEP bodies · 6,626 TET10 (12,981 nodes, 38,943 DOF)
Cycle Trajectory
17 steps (unloaded #1 → insert #2–#8 → pinch #9–#12 → extract #13–#17)
Throat Snap-Back
|u_el| = 1.237 mm (throat) → 0.084 mm (locked window, -93%)
Pinch Release Force (Target 10 N)
F_pinch = 10.09 N at uy = 0.68 mm (Δ = 0.9%)
Peak Cauchy von Mises Stress
σ_vm = 12.5 MPa (pinch) / 6.1 MPa (insertion)

1. Geometry & FEA Mesh

  • •Two parametric B-Rep STEP solids generated via OpenCascade / build123d with 73 CAD faces and 18 semantic contact/boundary tags.
  • •Curved second-order tetrahedral mesh (6,626 TET10 elements, 12,981 nodes, 38,943 DOF) with 100% CAD boundary conformity and zero inverted elements.
  • •All 17 load-step snapshots (including bit-exact zero unloaded initial Step #1 and final Step #17) embedded in snap_fit_buckle.wce.

2. Loads & Boundary Conditions

  • •Female housing anchored at the rear strap slot face (ux = uy = uz = 0) with Z-symmetry plane constraints (uz = 0).
  • •Purely displacement-controlled loading with zero applied forces: axial drive displacement ux prescribed on the rear face of the male clip across Steps #1–#17.
  • •During Stage 2 (Steps #9–#12) and throat re-entry (Step #13), inward transverse displacement uy = ∓0.17…0.68 mm is prescribed on the top and bottom pinch pads.

3. Simulation Results & Findings

  • ✓Stage 1 (Insertion, Steps #1–#8): starts at 0 MPa / 0 mm (Step #1), reaches peak cantilever deflection |u_el| = 1.237 mm (σ_vm = 6.1 MPa) in the throat (Step #6), and snaps into the side windows onto the retention ledges with |u_el| dropping by 93% to 0.084 mm (Step #8).
  • ✓Stage 2 (Pinch Release, Steps #9–#12): inward pinch pad travel of 0.68 mm deflects the locking hooks to |u_el| = 0.710 mm (clearing the 0.70 mm throat undercut) with reaction force F_pinch = 10.09 N and peak bending stress σ_vm = 12.5 MPa.
  • ✓Stage 3 (Extraction, Steps #13–#17): clip is pulled backward (-X) through the throat and entry ramps, returning to the completely unloaded zero state at Step #17 (|u_el| = 0.000 mm, σ_vm = 0.0 MPa).
Enterprise & Engineering Workflow

Demonstrates WebCAE's ability to simulate multi-stage displacement-controlled snap-fit assembly and release cycles on quadratic 3D B-Rep meshes, directly verifying insertion force, retention lockup, and ergonomic 10 N pinch release constraints.

Launch Case in Web App →
14-Day Free Trial · $0 Due Today
$99/ mo (billed monthly after 14-day trial)

14 days of full Pro access. The first charge occurs only after 14 days unless canceled beforehand.

  • ✓14-Day Trial ($0 Today) (cancel anytime)
  • ✓Up to 1.5M+ DOFs (direct sparse solver)
  • ✓Native Windows, macOS & Linux Apps (100% offline)
  • ✓Nonlinear Contact & Buckling (Kσ, MITC4, RBE2/RBE3)

$0 due today. First charge occurs in 14 days unless cancelled. Cancel anytime in 1 click in your account.

Need bespoke solver development or a Dedicated Cloud VPS (128+ GB RAM, 32 cores)?
We build turnkey industry FEA pipelines and custom material models for engineering teams.

Ask an Engineer About Your Model

Describe your part, load case, or CAD format — we reply within 2 business hours.

WebCAE AI Assistant in bottom-right ↘

Want an instant answer on FEA theory or this model?

Click the AI chat button in the bottom-right corner to ask about boundary conditions, stress criteria, mesh convergence, or DSL scripting.

We use essential cookies to run this site, plus analytics cookies if you agree. Privacy Policy